A fixed amount of undiluted drug is electrically supplied to the spray chemical tank according to the injection amount and pump operating time.

It is a device that uses the water pressure on the primary side to suck in undiluted solution or high-concentration chemical solution and supply it to the chemical solution tank.
Since the dilution setting of 50 to 500 times is possible, it can correspond to the dilution of many drugs.
In addition, the dilution can be set without using electricity, which saves the labor of the operator.

It is a device that installs a propeller in the tank and stirs it.
This type is especially used when the shape of the tank is large, and can be retrofitted depending on the situation.

It is a device that creates a water flow by a circulation pump and stirs the inside of the tank.
It is a pre-installed pump that can be attached to any type regardless of the shape of the tank.

The pH value in the chemical tank can be displayed, and dilution control can be performed based on that value.

The pH value in the chemical tank can be displayed, and dilution control can be performed based on that value.In the case of dilution outside the set range, it is possible to issue an alarm and notify the administrator.

A compressor is used to prevent freezing by preventing chemicals from remaining in the piping.
No extra wiring is required during construction, and it can handle up to -5°C.

Freezing is prevented by wrapping heat rays around chemical piping and hoses.
It is the most common anti-freezing method and can usually handle up to -7°C.
※The cold-resistant temperature changes with the combined use of heat insulating material.

Freezing is prevented by warming the antifreeze and keeping it circulating.
It can be used even in extremely cold regions up to -15°C.

The combination of liquid circulation and air blow prevents freezing even in extremely cold regions above -15°C.
※We also have a track record at -305°C. (Hokkaido)（Depends on the installation environment）。

It is possible to switch the spray time according to the type of vehicle, the size of the vehicle, the outbound and inbound routes, the presence or absence of loads, etc.
There are cases such as injection for 10 seconds for small cars and spray for 20 seconds for large vehicles.

It is possible to switch the spray position according to the type of vehicle, the size of the vehicle, the outbound and inbound routes, the presence or absence of loads, etc.
When the loading platform on the return route is emptied by an animal carrier, there are cases where the outbound route is side spray to the tires and the return route is full-scale spray, or only vehicles loaded with animals are reciprocally injected, and small vehicles are injected only on the outward route.

It is possible to switch the propellant solution according to the type of vehicle, the outbound and inbound routes, and the presence or absence of loads.
In some cases, the vehicle is washed with a preliminary spray of water before spraying the chemical solution to obtain a reliable disinfecting effect, and in the event of a plague, a different chemical solution is sprayed.
In some cases, when the vehicle leaves the vehicle, a cleaning solution is sprayed to clean the disinfectant solution at the time of entry.We can also propose electrolyzed water disinfection.

As with coin parking and railroad crossings, it is possible to stop the vehicle with certainty.
By installing the breaker in front of the spray nozzle, it is possible to prevent slipping through, and by installing the breaker behind the spray nozzle, it is possible to reliably spray the disinfectant solution into the vehicle.

It is possible to stop the vehicle at the red and blue traffic lights.
By linking the traffic light and the sensor, you can make the signal turn blue when the vehicle has finished spray disinfection.The timing at which the signal changes can be changed arbitrarily by control.

It is a function to count the number of vehicles by day of the week or season.
This makes it possible to understand the amount of chemicals used, the amount of electricity and water used, and to plan and manage maintenance schedules.

The initial cost is low and it is a type that is easy to introduce.

Since it is a wireless type, it can be installed easily and can be retrofitted.

It is a function to set the power on / off of the disinfectant equipment and other peripheral devices for each device from the period unit to the hour unit.
This makes it possible to prevent malfunction of the sensor outside the operating hours and prevent forgetting to operate the antifreeze device that operates for a period of time.

It is a function that sounds an alarm when there is a shortage of undiluted chemicals or a device failure, and at the same time sends the contents to a terminal such as a mobile phone.
As a result, the initial movement can be made faster and the operation stop time can be shortened.Also, by saving and aggregating the error history, it can be useful for advance maintenance planning.